平面波输入下海水-海床-结构动力相互作用分析

海洋工程结构的地震反应分析是保证海洋工程结构地震安全的重要环节.由于其所处的复杂环境, 该问题涉及到流固耦合和土-结相互作用.本文基于海水、饱和海床、基岩流固耦合统一计算框架,采用Davidenkov模型和修正的Masing准则考虑饱和海床的非线性,在脉冲SV波垂直入射下, 进行了海域场地和海洋工程结构的动力响应分析. 首先,对比分析了线性自由场和非线性自由场输入情形的海域场地非线性反应,结果表明线性自由场输入时反应不合理,自由场分析和场地分析应该采用相一致的本构模型. 然后,对比分析了海床分别为线性和非线性情形时,海域场地以及海水-海床-结构体系的反应特征. 与线性海床情形相比,非线性对海床反应的影响主要由如下两方面因素控制: 一方面,非线性导致饱和海床模量减小, 饱和海床与基岩间的波阻抗比减小,由基岩到饱和海床间的反射系数和透射系数增加, 导致反应增大; 另一方面,非线性导致阻尼加大, 使海床反应减小. 对于本文算例而言,阻尼对非线性海床结果的影响占主导作用.      

pH/temperature double responsive behaviors and mechanical strength of laponite‐crosslinked poly(DEA‐co‐DMAEMA) nanocomposite hydrogels

A nanocomposite (NC) hydrogel crosslinked by inorganic Laponite XLG was successfully synthesized via in situ free radical polymerization of monomers N,N‐diethylacrylamide and (2‐dimethylamino) ethyl methacrylate (DMAEMA). Polymerization was carried out at room temperature due to the accelerating effect of DMAEMA. The as‐prepared hydrogels displayed controlled transformation in optical transmittance and volume in response to small diversification of environmental factors, such as temperature and pH. The compressive strength of swollen D_6:1G₆ hydrogels was as high as 2219 kPa while compressive strain was 95%. Cyclic compression measurement exhibited good elastic properties of NC hydrogels. This work provides a facile method for fabricating stimuli‐responsive hydrogels with superior mechanical property. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 876–884     

Attapulgite grafted with polystyrene via a simultaneous reverse and normal initiation atom transfer radical polymerization

The surface grafting of attapulgite (ATP) with polystyrene (PS) was established via a simultaneous reverse and normal initiation atom transfer radical polymerization (SR&NIATRP). 4‐(chloromethyl)phenyltrimethoxysilane (CMPTMS) chemical bounded on the surface of ATP (ATP‐Cl, Cl‐I) was prepared via one‐step self‐assembly. SR&NI ATRP of styrene was conducted using CuCl₂ complex tris(2‐(dimethylamino)ethyl)amine (Me₆‐TREN) as the catalytic system, initiated by 2,2‐azobis(isobutyronitrile) (AIBN) and ATP‐Cl. FT‐IR, XRD, XPS, TGA and TEM data were consistent with the grafting of benzyl chloride groups and PS chains on ATP surface. The controllability of polymerization was investigated by the kinetics behavior under different molar ratio of AIBN and CuCl₂. The obtained polymer possessed a uniform distribution of molecular weights with a lower polydispersity index of 1.2～1.4. The relationship between polymerization on the surface of ATP and in solution was discussed in detail based on TGA data of hybrid particles and GPC trace of free polymer in solution. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1508–1516     

西北太平洋表层沉积物地球化学特征及其物源指示意义

为深入了解西北太平洋表层沉积物地球化学特征及物质来源，对大洋40航次在西北太平洋马尔库斯-威克海山区采集的表层沉积物进行了全岩地球化学和黏土矿物测试分析。结果表明，研究区表层沉积物稀土元素（REE)平均质量分数为302.87×10^-6，北美页岩标准化稀土配分模式与黄土相似，并具Ce轻微负异常和Eu无异常特征。稀土配分模式、判别函数（discriminant functions,DF）、M/I（蒙脱石/伊利石）及涂片鉴定等结果指示沉积物物源具有多源性，主要为陆源风尘物质，并受海洋自生物质的强烈影响，海山玄武岩及其蚀变产物和硅质生物也有一定的贡献。研究区沉积物稀土特征既不同于边缘海沉积物，也有别于远洋沉积物，而与弧后盆地沉积物类似。结合1/δCe-LREE/HREE和LREE/HREE-Y/Ho判别图解结果，研究区沉积物物源结构属性应介于边缘海沉积物与远洋沉积物之间，为洋陆过渡区沉积。     

AEIV结合AHSI用于饱和脂肪酮类物质的13C NMR谱模拟

应用一种反映分子局部微环境描述子--原子电性相互作用矢量（vector of atomic electronegative interaction,AEIV）和原子杂化状态指数（Atomic Hybridation State Index, AHSI）对饱和脂肪酮类化合物的55种分子中的153个¹³C NMR谱建模模拟,应用多元线性回归方法得到定量结构波谱关系(QSSR)模型的复相关系数R_MM=0.997, 标准偏差为SD_MM=7.155. 采用留一法交互检验的结果是R_CV=0.993,SD_CV=10.195. 并随机抽出三部分分子进行检验,得到的相关系数分别是R_MM1=0.996,R_MM2=0.996,R_MM3=0.999. 研究结果表明使用AEIV和AHSI所建模型预测能力是相当稳定的.     

Transition Metal Free Chemoselective Reduction of α,β‐Unsaturated Ketones to Saturated Ketones Using Tosyl Hydrazide as a Hydrogen Donor

An efficient, inexpensive and simple method for the reduction of various α,β‐unsaturated ketones to corresponding saturated ketones using tosyl hydrazide as a hydrogen donor in DMF using calcium oxide powder has been reported. A variety of enones underwent reduction without forming undesirable side products. High chemoselectivity, broad functional group tolerance and good yields are the noteworthy features of this protocol.     

Antibacterial and antifungal LDPE films for active packaging

Active antimicrobial packaging is a promising form of active packaging that can kill or inhibit microorganism growth in order to maintain product quality and safety. One of the most common approaches is based on the release of volatile antimicrobial agents from the packaging material such as essential oils. Due to their highly volatile nature, the challenge is to preserve the essential oils during the high‐temperature melt processing of the polymer, while maintaining high antimicrobial activity for a desired shelf life. This study suggests a new approach in order to achieve this goal. Antimicrobial active films are developed based on low‐density polyethylene (LDPE), organo‐modified montmorillonite clays (MMT) and carvacrol (used as an essential oil model). In order to minimize carvacrol loss throughout the polymer compounding, a pre‐compounding step is developed in which clay/carvacrol hybrids are produced. The hybrids exhibit a significant increase in the d‐spacing of clay and enhanced thermal stability. The resulting LDPE/(clay/carvacrol) films exhibit superior and prolonged antibacterial activity against Escherichia coli and Listeria innocua, while polymer compounded with pure carvacrol loses the antibacterial properties within days. The films also present an excellent antifungal activity against Alternaria alternata, used as a model plant pathogenic fungus. Furthermore, infrared spectroscopy analysis of the LDPE/(clay/carvacrol) system displayed significantly higher carvacrol content in the film as well as a slower out‐diffusion of the carvacrol molecules in comparison to LDPE/carvacrol films. Thus, these new films have a high potential for antimicrobial food packaging applications due to their long‐lasting and broad‐spectrum antimicrobial efficacy. Copyright © 2014 John Wiley & Sons, Ltd.     

磷酸浸渍黏土砖中五氧化二磷含量测定方法的改进

研究了磷钼酸铵容量法测定磷酸浸渍黏土砖中五氧化二磷含量的方法,对国家标准分析方法进行了改进,讨论了不同实验条件对实验结果的影响,并进行了精密度和准确度实验。结果准确、重现性好,证明方法可靠。     

Delamination of sodium montmorillonite in PA6 in the presence of melamine polyphosphate

This study describes the influence of melamine polyphosphate (MPP) flame retardant addition on layered structure of virgin sodium montmorillonite (MMT) in PA6/MMT system obtained in extrusion process. It was found that the extrusion of the PA6/MMT binary system in co‐rotating twin screw extruder gives intercalated clay nanocomposites, while during extrusion of ternary PA6/MMT/MPP composite, full exfoliation of clay was obtained in the system. Structure of the composites was proved utilizing wide angle X‐ray scattering and transmission electron microscopy techniques. Exfoliation of MMT in ternary PA6/MMT/MPP system was also confirmed by rheological studies (viscosity and creep measurements) which were carried out using rotational rheometer. Young's modulus of PA6/MMT/MPP was found to be ~25% greater comparing to PA6/MPP of the same filling level. Cone calorimetry experiments proved decrease of heat release rate peak of PA6/MMT/MPP by ~55% comparing to PA6/MPP with the same total filling level. Copyright © 2017 John Wiley & Sons, Ltd.     

Improving the water resistance of epoxy–anhydride matrices by the incorporation of bentonite

Epoxy–anhydride‐based polymers are commonly used as a matrix in pipeline systems exposed to water during their in‐service life. Water absorption at moderate temperatures and/or at long exposure times could lead to irreversible hydrolysis reaction decreasing considerably the polymer overall performance. A strategy to enhance the barrier properties of epoxy resins is to add nanofillers to traditional matrices. In this work, we added bentonite and chemically modified bentonite to this purpose. Water absorption of the resulting materials at three different temperatures (22°C, 80°C, and 93°C) was studied, and simultaneously, the evolution during the immersion tests of glass transition temperature and flexural modulus was recorded. Long‐term gravimetric results showed that composites with chemically modified bentonite produce a delay on the hydrolysis of epoxy–anhydride matrix, which is a relevant result, because of the tough application and uses of the system, from the technological point of view. Copyright © 2016 John Wiley & Sons, Ltd.